How to control a brushless motor through an ESC and RC Signal Generator

28/06/2019 RAJ SHARMA Leave a comment

Here is a simple test setup of RC brush-less motor using ESC driver and RC signal generator. RC signal generator based on PIC12F675 microcontroller, Hex code and the circuit is available. The term ESC stands for “electronic speed control.

Download Hex Code

Complete Project Available Here

tagged with RC brushless motor driver, RC motor driver

Motor Driver DC
Uncategorized

DDS Module AD9833 , Output 0 to 200KHz , Potentiometer and Arduino

15/09/2022 RAJ SHARMA
Car LED Head-Lamp Fade effect – arduino project

27/11/2020 RAJ SHARMA
2 Digit Counter Using 7 Segment display and pic16f1825

05/09/2020 RAJ SHARMA
3 Phase EMC/EMI Filter Circuit 480V/16Amps (Common Mode Choke)

29/07/2020 RAJ SHARMA

Circuits & Projects

Search for:

Sound To Light Effect Circuit

Electronics Work Bench

Window Comparator

LED DIMMER

PS2 Wireless Remote Robot Controller

Clap Switch with Timer

Who Won

Metal Detector Schematic

3 WHEEL ROBOT CHASSIS

RC SIGNAL MONITOR USING 20 SEGMENT BAR-GRAPH LED

RC SIGNAL MONITOR AND SWITCH

Mini Microphone Pre-Amplifier

1.6KW Brush=Less Motor Power Driver

Electret Micro-Phone Pre-Amplifier

DDS Module AD9833 , Output 0 to 200KHz , Potentiometer and Arduino

15/09/2022 Leave a comment

Simple DDS module test Video Code and Connections

1600W Titanium server power supply with 600V CoolMOS G7 in DDPAK and digital control by XMC

05/07/2022 Leave a comment

This Infineon evaluation board (EVAL_1K6W_PSU_G7_DD) represents a complete system solution for a 1600W server power supply (PSU) which achieves the 80Plus® Titanium® standard. The power

LOAD CELL FORCE SENSOR INSTRUMENTATION AMPLIFIER -analog output

28/11/2020 Leave a comment

Here is my newly developed Load Cell amplifier circuit. Circuit provides very accurate reading. I have tested this circuit with 5Kg Load Sensor. Output is

Car LED Head-Lamp Fade effect – arduino project

27/11/2020 Leave a comment

This example demonstrates the use of the fading an LED Car Head-Lamp off and on. Analog Write uses pulse width modulation (PWM), turning a digital

230V AC Lamp Flasher Using arduino and ssr ( solid state relay)

02/11/2020 Leave a comment

Here is a simple Arduino Lamp flasher project, i have used optically isolated Solid State Relay ( SSR) to drive the AC Load, Arduino provides

2 Digit Counter Using 7 Segment display and pic16f1825

05/09/2020 Leave a comment

The Two Digit UP Counter project built using PIC16F1825 Microcontroller from Microchip, CAT4016 serial to display driver IC from ON-Semiconductor and two 7 Segment common

0.5A to 4AMPS VOLTAGE CONTROLLED CURRENT SOURCE

15/08/2020 Leave a comment

This is very accurate voltage to current source, can be used in many applications such as LED drivers, TEC drivers, Power Supply, Battery charger. Download

Arduino compatible one channel relay-tsop1838 ir sensor-oled-lm35-drv5053 sensor board

09/08/2020 Leave a comment

This project consist OLED Display, One channel Relay, LM35 Temperature Sensor, DRV5053 Magnetic Sensor, ATMEGA328 Chip. Project is Arduino compatible and provided with connector for

Arduino Shield One Relay-10 LED BarGraph-Current Sensor

08/08/2020 Leave a comment

This Arduino Nano shield has following features , Current Sensor INA198, 2 Tactile Switch, One Channel Relay , 10 LED’s Bar-Graph , TSOP1838 Infra-Red

Over Current Alarm Using Buzzer-15LEDs Bar-Graph Arduino Compatible

05/08/2020 Leave a comment

Here is my new project which is Arduino compatible. It is 15 LED’s barograph over current alarm, 01 to 15 LEDs display current range 350mA to

How to control a brushless motor through an ESC and RC Signal Generator

Related Posts

Leave a Reply Cancel reply