LUX Meter project has been design to measure the illumination. Illumination is luminous flux falling on surface area of photo diode. This illumination converted to corresponding voltage using Op-Amp circuit.
- Supply 9 VDC PP3 Battery @ 20 mA
- Onboard Photo Diode
- Onboard preset for calibration
- Range selection via jumper 10mV/LUX, 1mV/LUX, 0.1mV/LUX
- Interfacing is via berg connector
- Power-On LED indicator
- Four mounting holes of 3.2 mm each
- PCB dimensions 53 mm x 38 mm
The project is designed around Texas instrument Op-Amp TLC271 which can operate from single supply with low bias current, here op-amp act as current to voltage converter. 5000 LUX (approx) can be measure with a voltmeter having 5V range. Meter is not provided.
- J1 Jumper : 10mV/Lux
- J2 Jumper : 1mV/Lux
- J3 Jumper : 0.1mV/LUX
- PR2 Preset : To Calibrate the meter
- PR1 Preset : Fine Gain adjustment for 10mV/Lux
- CN1 Connector : Supply 9 VDC (PP3 9V DC Battery Ideal) and Output Voltage
- D2 LED : Power Indicator
- D1 LED : Photo Diode (Sensor)
Standard incandescent 100W lamp should be used for approximation calibration. To make Calibration select the 1mV/Lux J2 Jumper, move the preset full in CCW. Connect the accurate voltmeter having range of 5V. Adjust the distance between the photo diode and Lamp so that voltmeter reads 0.38V0. At this point, illumination on photodiode surface is about 100 Lux (aprox). And then adjust the PR2 so that voltmeter reads 1V. Calibration has now been complete. This project is based on Hamamatsu Photo Diode Application
2 Digit Count Down Timer is a utility Count Down timer project for upto 99 seconds of countdown time. This project can find many uses in your shack and home. The relay output remains on during the Count Down period, allowing you to interface load or alarm that you want to keep it on for a certain amount of time (in seconds).
- Micro-controller based design for greater accuracy and control
- Power supply input 12 VDC 200 mA
- Two 0.5″ display segments to display time
- 12V SPDT (Single Pole Double Throw) relay for alarm use
- Single key start and dual key alarm time set function
- Power and Relay-On LED indicator
- Terminal connectors for connecting power supply input and relay output to the PCB
- Onboard regulator for regulated supply to the kit
- Crystal resonator based design for better accuracy
- PCB dimensions 72 mm x 81 mm
This is a micro-controller based 2 Digit (99 Seconds) Count Down Timer. This Count Down Timer is very easy to use and easy to configure. This project can find a lot of application areas where you need a device to remain ON (or OFF) for a certain period of time (upto 99 Seconds). Power to the circuit is applied at CN1 (12 VDC). D1 provides the reverse polarity protection to this kit. LED D2 confirms DC Power Supply to the board. S1 and S2 displays Count Down time. J3 provide an easy way of connecting external switches to this board. LED D4 confirms the relay status.
The setting up of countdown period and START Function for this project is accomplished with the help of 3 tactile switches shown as SW1, SW2 and SW3 in the schematic and labeled as UP, DOWN and SET on the PCB respectively.
- Setting Time : The default value is shown on display S1 and S2 respectively. You can change this value by simply pressing the UP and DOWN key.
- Start : You can start the Count Down by pressing SET key. When the Count Down starts the relay is energized, indicated with the glow of LED D4. Once the Display (S1 and S2) reaches 0 the relay is de energized.
Dark activated LED light is a simple project which operates a LED when the light falling on the LDR goes below a set point. The circuit is built using LM393 comparator, LDR as light sensor, preset (potentiometer) for sensitivity adjustment, transistor to drive the LED. The project can also be considered for use in energy saving application.
- Input – 12 V @ 1A
- LED 12V 500mA Maximum (6W)
- Onboard Preset for Level Adjust
- Operation LED Indicator
- On Board Power LED
- Header Connector for Power Supply and LED
- PCB dimensions 55.45MM X 12.70 MM
PROJECT PICTURE BACK SIDE
16 Channel Infra-Red remote controller is based on PIC16F73 Micro-controller from Microchip. The receiver part follows RC5 (Philips) Code Format. Tiny receiver provides 16 latch outputs or 8 Latch + 8 Momentary outputs by closing Jumper J1. All outputs are TTL and can drive Relay board or solid state relay. The circuit uses TSOP1738 Infra-Red receiver module which provides high degree of noise immunity against interfering light source.
- Supply Remote Transmitter RC5 Philips 2XAAA Battery
- Supply Receiver 7V to 12V DC
- Modulation 38Khz
- Philips RC5 Code Format
- Operating range up to 20 feet
- 2 Pin Screw Terminals for Supply Input
- On Board Power LED
- Onboard VT (Valid Transmission) LED
- All Outputs TTL Level provided with Header Connector
- Jumper (J1) for Mode Selection
- J1 Open 16 Latch Outputs
- J1 Closed 8Latch + 8 Momentary
- Home Appliances
- Remote Door closer
- Remote Curtains
- Security Systems