Circuit Ideas I Electronic DIY Projects I Robotics
High Current PWM Halogen Dimmer controller project is designed around SG3525 IC and High current MOSFET. Project can handle lamp up to 5 Amps (10Amps Possible with big heat sink) and supply 12-24V DC .Ideal for Halogen Dichroic Lamp or Halogen Lamp. Features Supply input 15 to 24 VDC Load-Lamp 12 to 24 VDC @ 5 Amps Load 10 amps
Read moreVoice Changer project can be used to transpose or distort one’s voice by encoding the sound appearing at the Microphone input. This project is built around AP8072 IC. Supply input : 6 VDC @ 200 mA Output : Speaker, 8 Ω / 0.5 W Audio amplifier type LM386 with volume control preset Jumper selectable tone frequency for encoding sound 4
Read more1.2W Audio Amplifier Project can be used as a low frequency class B power amplifier with wide range of supply. Power supply – 3 – 12 VDC Output – 1.6 W, 4 Ω / 1.2 W, 8 Ω Input resistance – 5 MΩ Low quiescent current, good ripple rejection and no cross-over distortion Onboard presets to adjust volume Terminal pins
Read more1.6W Mono Audio Amplifier Project is based on TDA7231, which is class AB power amplifier with a wide range of supply. Power supply: 5 To 12 VDC Output: 1.6 W, 4 Ω / 1 W, 8 Ω Low crossover distortion, soft clipping PR1 Preset for Volume Adjust Terminal pins for connecting power supply, input and output Power On/OFF Switch Power-On
Read moreThe small 2 Channel amplifier constructed around Sanyo’s LA4445 IC delivers 5.5Watts +5.5 Watts at 4 ohm load, supply in 12V DC 2Amp, Input impedance 30K. Features Dual Channels output : 5.5w Minimum External Parts Very small pop noise at the time of power supply ON/OFF Good ripple rejections Small residual noise Built-in protectors 1. Thermal Protector 2.
Read moreThe module has been designed around LMD18200 from Texas Instruments. The LMD18200 is a 3A H-Bridge designed for motion control applications. The device is built using a multi-technology process which combines bipolar and CMOS control circuitry with DMOS power devices on the same monolithic structure. Ideal for driving DC and stepper motors; the LMD18200 accommodates peak output currents up to
Read moreThe project designed around L293D IC. The L293D device is quadruple high-current half-H driver. The 293D is designed to provide bidirectional drive current up to 600mA a voltage from 5V to 36V.L293D Adapter Board can be used as dual DC motor driver or bipolar stepper motor driver. Useful in robotics application, bidirectional DC motor controller and stepper motor driver. Separate
Read moreAC Solid state Relay for Inductive Load offers simple On/Off type Switch Control with TTL compatible input signal. Input signal : 2 ~ 5 VDC, TTL compatible Output : up to 500 W Mains supply input 230 VAC or 110 VAC Optically isolated Triac based design Power Battery Terminal (PBT) and Terminal pins for easy input / output connection Four
Read moreThis Project provides Positive and Negative (Dual Output) 5 V @ 1 A Regulated Power Supply. Input 7-0-7 VAC to 12-0-12 VAC or +/- 9 to 18 VDC Output : Dual output ± 5 V @ 1 A regulated low ripple DC voltage Heat-sink for regulator ICs Onboard bridge rectifier to convert AC to DC LED indication for both the
Read moreThe Project is based on LV8727E IC from ON Semiconductor. The LV8727 is a PWM current-controlled micro step bipolar stepping motor driver. This driver can provide eight ways of micro step resolution of 1/2, 1/8, 1/16, 1/32, 1/64, 1/128, 1/10, 1/20, and can drive simply by the step input. This Bipolar Driver works with supply input 9V to 36V (Replace
Read more