Digital 2 Digit 7 Segment Thermometer Using PIC1825, CAT4016, DS1820

This digital Thermometer provides real-time temperature values from 00 to 99 degrees Celsius. The Temperature Monitor  project built using PIC16F1825 Microcontroller from Microchip, CAT4016 serial to display driver IC from ON-Semiconductor, DS18200 Temperature sensor and two 7 Segment common anode 0.5 Inch display. This little handy project consumes low current and can be work with 4.5 V batteries, intensity of

Read more

0 To 1Amp Bar-Graph Current Monitor Using PIC16F886 and 20 SMD LEDs

Tiny Bar-Graph displays provide a Red color bright, easy to read display of current range from 0 to 1A.  This Bar-Graph has 20 segments in single color and display 0 to 1Amp Current. The Barograph current   monitor is based on PIC microcontroller with 10 Bit resolution ADC.  This high performance measurement provides unique capabilities and can be used in various

Read more

0 To 5V Bar-Graph Voltage Monitor Using 20 LED & PIC16F886 SMD Board

Tiny Bar-Graph displays provide a Red color bright, easy to read display of Voltage range of 0 to 5V.  This Bar-Graph has 20 segments in single color and display 0 to 5V DC. The Barograph Voltage   monitor is based on PIC microcontroller with 10 Bit resolution ADC.  This high performance measurement provides unique capabilities and can be used in various

Read more

RTC( Real Time Clock) Module Using SMD Components and DS1307

The module based on DS1307, The DS1307 serial real-time clock (RTC) is a low-power, full binary-coded decimal (BCD) clock/calendar plus 56 bytes of NV SRAM. Address and data are transferred serially through an I²C, bidirectional bus. The clock/calendar provides seconds, minutes, hours, day, date, month, and year information. The end of the month date is automatically adjusted for months with

Read more

USB To UART Converter Using MCP2200

The Module is based on The MCP2200, which is a USB-to-UART serial converter which enables USB connectivity in application that have a UART interface. The device reduces external components by integrating the USB termination resistors. The MCP2200 also has 256-bytes of integrated user EEPROM. The MCP2200 has eight general purpose input / output pins. Four of the pins have alternate

Read more

18 Pin PIC Micro-Controller Development Board

The PIC 18 PIN (DIP) Development / Evaluations Board demonstrates the capabilities of Microchip’s 8-bit microcontrollers, specifically, 18 Pin PIC16F1847. It can be used as a standalone demonstration board with a programmed part. With this board you can develop and prototype with all Microchip’s 18 PIN PIC microcontrollers. The board has a Reset switch and status LEDs. On board 3.3

Read more

40 Pin & 28 Pin PIC Micro-Controller Development Board With On Board 3.3V & 5V Switching Regulator

The PIC 40 / 28 PIN (DIP) Development / Evaluations board demonstrates the capabilities of Microchip’s 8-bit microcontrollers, specifically, 28- and 40-pin PIC16FXXX, PIC16F1XXX, and PIC18 devices. It can be used as a standalone demonstration board with a programmed part. With this board you can develop and prototype with all Microchip’s 40 & 28 PIN PIC microcontrollers which doesn’t require

Read more

4 Channel Transistor Based Output Driver For Unipolar Stepper Motor Driver and Relay , Solenoid Driver

Unipolar 4-Phase Stepper Motor Controller Board will help you control a Stepper Motor or 4 individual Solenoids. This circuit consisting of transistors that serve as current amplifier and also diode to prevent damaging back EMF, circuit uses Darlington transistors to provide high current capacity to unipolar stepper motor. Just provide sequence of pulse using Micro-Controller or desceret circuit to roll

Read more
1 2 3 23