Universal Dual Op-Amp Development PCB & Schematic using THT Components

The Universal Op-Amp Development board is a general purpose blank circuit boards that simplify prototyping circuits for a variety of Op-Amp circuits. The evaluation module board design allows many different circuits to be constructed easily and quickly.

Universal Dual Operational Amplifier (Op-Amp) board is designed to aid in the evaluation and testing of the low voltage/low power and some precision operational amplifiers. This board will accommodate Dual op amp that are assembled in a 8 Pin Dip package. This board is designed to use single or dual amplifiers. Many different circuits can be made such as inverting, non-inverting, differential-In amplifiers and low-pass, band-pass, band reject, or notch second order filters. The amplifier can be powered with single or dual supplies. These circuits can be configured without any modifications to the board, all that is necessary is to select the correct resistors and capacitors. The other optional components can be left open or shorted depending on the configuration desired.

Power is applied to the Header connector pins labeled VCC,-VEE, GND, If a single supply is used, then -VEE should be connected to GND.

This board mainly support lots of Texas instruments Op-Amps, On Semi, Analog Devices

List Of Op-Amps Can be use

  • OPA2350
  • OPA2340
  • LM358
  • LF422

 

 

 

 

 


Inverting Operational Amplifier Circuit ( Universal Op-Amplifier Development Board)

This is most widely used operational amplifier circuit.  It is an amplifier whose closed-loop gain is set by R27 & R18. It can amplify AC or DC Signal.


Non Inverting Operation Amplifier ( Universal Op-Amplifier Development Board)

This simple circuit is a non-inverting Operation Amplifier can be made using universal Op-Amplifier Development Board. Output voltage has same phase as the input voltage ( For DC Input)

DC Solid State Relay Using Mosfet & Optically Isolated Gate Driver With Current Feedback & Fault Output

DC solid state Relay build using optically isolated Mosfet gate driver & high current Mosfet, this relay also provides current feedback as voltage output and fault TTL voltage output when  current goes above set point.  Current feedback designed around op-amp  as signal conditioning  which measure the current across low ohm shunt resistor.  On board preset (trimmer pot) to adjust the fault current set point.  Normally current fault output is high TTL it goes low if fault condition occurs.  Circuit available at www.twovolt.com

 

  • DC Supply 90V DC Maximum
  • Maximum Current Load 15Amps
  • Gate Driver Supply 15V DC

 

Arduino Based open Source Robot Controller With I/Os using Dual LMD18201 3Amps Each H-Bridge Motor Driver & Sensors ( Compatible with M-BOT )

Arduino Based open Source Robot Controller With I/O using  Dual LMD18201 3Amps Each H-Bridge Motor Driver & Sensors ( Compatible with M-BOT  )

 

 

  • LMD18201X2 Motor Driver IC
  • Infra-Red Receiver TSOP1738
  • On Board Infra-Red LED
  • Multiple I/O Connectors for Sensors, Encoders
  • On Board LDR as Light Sensor
  • Onboard Piezo Buzzer
  • On Board Power LED

 

Arduino Based open Source Robot Controller With I/Os using Dual L293 h-Bridge Motor Driver & Sensors Compatible with M-BOT

Arduino Based open Source Robot Controller With I/Os using  Dual L293 h-Bridge Motor Driver & Sensors Compatible with M-BOT

Board Includes following Things

  • L293X2 Motor Driver IC
  • Infra-Red Receiver TSOP1738
  • On Board Infra-Red LED
  • Multiple I/O Connectors for Sensors, Encoders
  • On Board LDR as Light Sensor
  • Onboard Piezo Sensor
  • On Board Power LED

DOWNLOAD SCHEMATIC PDF

DOWNLOAD PCB PDF

 

Reflective Object Sensor- Infra Red Optical Proximity Switch Using PLL LM567

Reflective Object Sensor- Optical Proximity Switch Using PLL LM567

The simple circuit is based on LM567 PLL IC and optical sensor QRD1114 from Fairchild semiconductor. The QRD11114 reflective sensor consists of an infrared emitting diode and an NPN silicon photo Darlington mounted side by side in a black plastic housing. The on-axis radiation of the emitter and the on-axis response of the detector are both perpendicular to the face of the QRD1113/14. The photo Darlington responds to radiation emitted from the diode only when a reflective object or surface is in the field of view of the detector.

  • Supply 5V DC
  • Output LED
  • Output TTL 5V
  • Sensing Distance Up to 15MM
  • Sensing Distance Adjustable

reflactive-object-sensor-infra-red-optical-proximity-switch-using-lm567-2

reflactive-object-sensor-infra-red-optical-proximity-switch-using-lm567-1

Dual-Channel Quadrature Hall-Effect Bipolar Switch Module For Magnetic Encoder for Motion Control application.

dual-channel-quadrature-hall-effect-bipolar-switch-to-make-magnetic-encoder-for-motion-control-application-1

Dual-Channel Quadrature Hall-Effect Bipolar Switch Module For  Magnetic Encoder for Motion Control application.

The A1230 is a dual-channel, bipolar switch with two Hall-effect sensing elements, each providing a separate digital output for speed and direction signal processing capability. The Hall elements are photolithographically aligned to better than 1 µm. Maintaining accurate mechanical location between the two active Hall elements eliminates the major manufacturing hurdle encountered in fine-pitch detection applications. The A1230 is a highly sensitive, temperature stable magnetic sensing device ideal for use in ring magnet based, speed and direction systems located in harsh automotive and industrial environments.

Featutrs

  • It Provides Dual A & B Channel Like optical Encoder
  • Simple Module help to make Magnetic Encoder for Motion Control application
  • Supply 5V DC
  • TTL Output
  • Two matched Hall-effect switches on a single substrate
  • 1 mm Hall element spacing
  • Superior temperature stability and industry-leading jitter performance through use of advanced   chopper stabilization topology
  • Integrated LDO regulator provides 3.3 V operation
  • Integrated ESD protection from outputs and VCC to ground
  • High-sensitivity switch points
  • Robust structure for EMC protection
  • Solid-state reliability
  • Reverse-battery protection on supply and both output pins

Applications

  • Brushless DC Motor Rotation
  • Speed Sensing
  • Pulse Counter
  • Magnetic Encoders

dual-channel-quadrature-hall-effect-bipolar-switch-to-make-magnetic-encoder-for-motion-control-application-2

dual-channel-quadrature-hall-effect-bipolar-switch-to-make-magnetic-encoder-for-motion-control-application-1

 

The A1230 monolithic integrated circuit (IC) contains two independent Hall-effect bipolar switches located 1 mm apart. The digital outputs are out of phase so that the outputs are in quadrature when interfaced with the proper ring magnet design. This allows easy processing of speed and direction signals. Extremely low-drift amplifiers guarantee symmetry between the switches to maintain signal quadrature. The Allegro patented, high-frequency chopper-stabilization technique cancels offsets in each channel providing stable operation over the full specified temperature and voltage ranges.

Additionally, the high-frequency chopping circuits allow an increased analog signal-to-noise ratio at the input of the digital comparators internal to the IC. As a result, the A1230 achieves industry-leading digital output jitter performance that is critical in high performance motor commutation applications. An on-chip low dropout (LDO) regulator allows the use of this device over a wide operating voltage range. Post-assembly factory programming at Allegro provides sensitive switch points that are symmetrical between the two switches.

Bipolar Switch Applications and Working from Allegro Micro
There are four general categories of Hall-effect IC devices that provide a digital output: unipolar switches, bipolar switches, omnipolar switches, and latches. Bipolar switches are described in this application note. Similar application notes on unipolar switches, omnipolar switches, and latches are provided on the Allegro™ website.

Bipolar sensor ICs are designed to be sensitive switches. (Note that the term “bipolar” refers to magnetic polarities, and is not related to bipolar semiconductor chip structures.) A bipolar switch has consistent hysteresis, but individual units have switchpoints that occur in either relatively more positive or more negative ranges. These devices find application where closely-spaced, alternating north and south poles are used, resulting in minimal required magnetic signal amplitude, ΔB, because the alternation of magnetic field polarity ensures switching, and the consistent hysteresis ensures periodicity.

dual-channel-quadrature-hall-effect-bipolar-switch-to-make-magnetic-encoder-for-motion-control-application-2

Applications for detecting the position of a rotating shaft, such as in a brushless dc motor (BLDC) are shown in figure 1. The multiple magnets are incorporated into a simple structure referred to as a “ring magnet,” which incorporates alternating zones of opposing magnetic polarity. The IC package adjacent to each ring magnet is the Hall bipolar switch device. When the shaft rotates, the magnetic zones are moved past the Hall device. The device is subjected to the nearest magnetic field and is turned-on when a south field is opposite, and turned-off when a north field is opposite. Note that the branded face of the device is toward the ring magnet.

 

 

1 2